• Takagi Tankless Water Heater with Direct Vent Kit TV-10, Remote Control and Pressure Valve - Natural Gas - T-KJR2-IN NG Kit 2

    - 140,000 Btu - Indoor Installation

    Product ID • TKJRNGKT2011

  • $609.75
  • Free Ground Shipping

Overview

The Takagi T-KJr2-IN Natural Gas is the smallest gas water heater in the Takagi tankless line. But this small and powerful unit - with gas inputs up to 140,000 BTU per hour - can meet all the hot-water needs of a small American home or apartment with one or two bathrooms. The compact, wall mounted T-K Jr2 supports hydronic baseboard or radiant floor heating applications, as well as provide domestic hot water to plumbing fixtures and appliances. The T-K Jr2 has an energy factor of 81% to 83%. At an average (rise in temperature) of 60°F in warmer areas - where the winter ground water is 60 Degree F and with the output set at 120 Degrees F - the unit will provide 3.8 GPM, or 228 GPH. The All new T-KJr2 has a max GPM of 6.6GPM.

Cost-efficient and environmentally friendly, the T-KJr2-IN can be converted into a direct-vent unit by using the optional TV10 conversion kit for installation in a garage, a utility closet or any confined space in which makeup air may be limited.

Kit 2 Includes : Cash Acme Commercial Pressure Relief Valve - 14737-0150 & Takagi TK-TV10 Direct Venting Kit

The Cash Acme FWL-2 is a pressure only relief valve designed specifically for the protection of tankless hot water supply systems where over-pressure conditions are likely to occur as a result of thermal expansion.

Completely automatic, the FWL-2 reseats after pressure relief. The valve may be installed directly on the tank or in a tee and is appropriate for either side (hot or cold) of the water heater.

The TK-TV10 direct vent conversion kit can be used to convert the tankless hot water unit from a conventional vent system to a direct vent (or sealed combustion) system.

Return Policy | Shipping Policy

Manuals & Docs

Technical Specs

Takagi Tankless Indoor Water Heater -- Natural Gas - T-KJR2-IN NG Techs and Specs

  • Gas Type
    Natural Gas
  • Power Input
    19,500 to 140,000 BTU
  • Water Pressure Minimum
    15 PSI
  • Maximum
    150 PSI
  • Gas Connection (Min)
    3/4 Inch Male NPT
  • Water Connection
    3/4 Inch Male NPT
  • Power Input Natural
    19,500 to 140,000 BTU
  • Water Pressure Minimum
    15 PSI
  • Maximum
    150 PSI
  • Gas Connection (Min)
    3/4 Inch Male NPT
  • Water Connection
    3/4 Inch Male NPT
  • Natural Manifold Pressure
    2 to 2.5 Inch W.C.
  • Propane Gas Manifold Pressure
    2.5 to 3.1 Inch W.C.
  • Electrical Supply
    120 Volts
  • Weight
    33 pounds
  • Dimensions
    (H x W x D) 20.5 inches by 13.8 inches by 6.7 inches
  • Maximun Water Flow
    6.6 GPM
  • Minimum Flow to Activate
    .5 GPM
  • Temperature Settings with Temperature Remote Controller
    99, 100, 102, 104, 106, 108, 109, 111, 113, 115, 117, 122, 131, 140, 158 and 167 Degrees
  • Exhaust Vent Size
    4 Inch Sealed Stainless Steel CAT III Vent Pipe
  • Max length
    50 Feet (subtract 5 feet each 90 degree elbow with a maximun 5 elbows)
  • Intake Vent Size (optional)
    4 Inch Piping
  • Ignition
    Electronic Ignition
  • Backflow Preventer
    TK-BF01 Required in weather condtions bedlow 36 F degrees
  • Vertical Condensation Drain
    Install per local code

Takagi Tankless Indoor Water Heater T-KJR2-IN NG Flow Rates (50 degree Input Water Assumed)

  • 90 Degree F rise / 2.5 gallons per minute
  • 80 Degree F rise / 2.9 gallons per minute
  • 70 Degree F rise / 3.3 gallons per minute
  • 60 Degree F rise / 3.8 gallons per minute
  • 55 Degree F rise / 4.2 gallons per minute
  • 50 Degree F rise / 4.6 gallons per minute

Cash Acme Commercial Pressure Relief Valve - 14737-0150

  • Specifically for the protection of hot water supply systems
  • 150 PSI
  • Compact and economical
  • Maximum temperature 210°F (hot water)
  • Every valve is tested for performance prior to shipping

Info & Links