Model TK-RE10
|
Temperature Remote Controller. The output temperature of the T-M32 / TM32 ASME can be controlled
with a TK-RE10 remote controller. It allows output temperatures beyond the factory settings and
shows error codes. The TK-RE10 also monitors incoming and outgoing water temperatures.
The temperature controller can adjust the output temperature from 100°F (38°C)
to 167°F (75°C).
Click here to purchase the TK-RE10
|
|
Takagi TK-KPWL4-2
Click to see more details
|
The TK-KPWL4-1 / TK-KPWL4-2 is used when terminating the venting through a sidewall.
Includes an outer sleeve wall thimble for penetrating through combustible
surfaces. The louver termination acts as a bird screen, restricting small
animals, pests, and foreign objects from entering into the vent system.
This sidewall termination is available in three different sizes, to cover
all ranges of wall thicknesses.
TK-KPWL4-1 for Wall from 4.2" to 6.0" with a 5.9" cut out hole.
TK-KPWL4-2 for Wall from 5.6" to 9.0" with a 5.9" cut out hole.
Click here to purchase the TK-KPWL4-1 or TK-KPWL4-2
|
|
Takagi TK-KPHT4
Click to see more details
|
The TK-KPHT4-1 / TK-KPHT4-2 is used when terminating the venting through a sidewall.
Includes an outer sleeve wall thimble for penetrating through combustible
surfaces. The Horizontal Hood can be used where the outside elements might
allow moisture in.
This sidewall termination is available in two different sizes, to cover
all ranges of wall thicknesses.
TK-KPHT4-1 for Wall from 4.2" to 6.0" with a 5.9" cut out hole.
TK-KPHT4-2 for Wall from 5.6" to 9.0" with a 5.9" cut out hole.
Click here to purchase the TK-KPHT4-1 or TK-KPHT4-2
|
|
Takagi TK-KPCT43
Click to see more details
|
The TK-KPCT43-1 / TK-KPCT43-2 Used when terminating direct-vent systems. For use with Takagi
direct-vent models that require a 3” intake and a 4” exhaust. The 4" exhaust connection connects up
to our 4" Z-Vent CAT III venting clamp side. This concentric termination provides
the convenience of only having to make one penetration through a sidewall instead of two separate
penetrations for the intake and exhaust piping. The louver termination acts as a bird screen,
restricting small animals, pests, and foreign objects from entering into the vent system. This
sidewall termination is available in three different sizes, to cover all ranges of wall thicknesses
This sidewall termination is available in two different sizes, to cover
all ranges of wall thicknesses.
TK-KPCT43-2 for Wall from 3.9" to 7.1"
TK-KPCT43-3 for Wall from 6.9" to 10.1"
Click here to purchase the TK-KPCT43-1 / TK-KPCT43-2
|
|
Model TK-BF01
|
The TK-BF01 Vent Damper prevents the backflow of air through the exhaust vent. This
helps prevent harmful exhaust gases from entering the home, as well as helping to prevent
the unit from freezing in areas where cold air can be blown or drawn into the exhaust
system. Required in weather condtions below 36 F degrees.
Click here for a TK-BF01 venting example
Click here to purchase the TK-BF01
|
|
TM-VC32 Outdoor Vent Cap
|
The TM-VC32 Vent Cap is for outdoor installation of the T-M32 tankless water heater.
The cap is installed on the top of the unit, instead of connecting an exhaust vent pipe.
The cap will prevent any debris that might be in the environment from entering the unit
and causing damage or a fire hazard, as well as preventing rain or other weather
from entering the unit.
Click here to purchase the TM-VC32
|
|
TM-DV32 Direct Vent Conversion Kit
|
The TK-DV32 Direct Venting Kit can be used to convert the T-M32 from a conventional vent
system to a direct vent (or sealed combustion) system. The TM-DV32 Direct Vent kit can be
used to convert the tankless hot water unit from a conventional vent system to a direct vent
(or sealed combustion) system.
Install this conversion kit in accordance with Takagi's
installation instructions and any applicable codes.
Click here to purchase the TM-DV32
|
|
TM-PC32 Pipe Cover
|
The TM-PC32 Pipe cover is designed to be attached directly to the bottom side of
the TM32 Tankless Water Heater to provide a cover for the pipe connection entry.
Click here to purchase the TM-PC32
|
|
TM-MC01 Multi
Unit Controller
|
The TM-MC01 Multi system controller is capable of handling up to 20 Takagi
T-M32 Tankless Water Heaters at one time. It also works as a diagnostic tool that
provides error codes.
Click here to purchase the TM-MC01
|
|
Z-Flex Venting
|
Z Flex Stainless Steel Venting Accessories with silicone free connections. See
our full line of pipe, exterior terminators, elbows and more. Perfect for vertical
or horizontal installation. Stainless Steel Venting is required for all Takagi
Water Heaters (Exhaust Only).
Click here to see sizes and prices for ZFlex Venting Supplies
|
|
Webstone Isolator EXP Valves
|
Easy two step installation of a Takagi T-M32 Tankless Water Heater with
unsurpassed safety, features and benefits. This is a complete inlet/outlet
valve system that provides everything you need for a secure installation
including full port testing and flushing of the system with easy to install
union connections.
Click here to see sizes and prices for Webstone Isolator EXP Union Valves
|
|
Falcon Stainless Steel Flex Pipes
|
Stronger and more flexible than copper with full flow/non-restrictive inner diameter.
Flows 134% more water than braided and flows 17% more water than copper. Resists work-hardening
and will not corrode, discolor or rust. Simpler installation versus hard pipe.
Click here to see sizes and prices for Falcon Stainless Steal 3/4 Inch Water Flex Pipes
|
